Ultrasonic Sensor HC SR04 with LCD Display (distance finder) #3 LCD

-




Ultrasonic Sensor HC SR04 with  LCD Display (distance finder)  #3 LCD



HcSr04 :)

     

         VCC      = Arduino 5V

         GND     =  Arduino GND

        ECHO    =  Digital 10 Pin

        TRIG      = DIgital 9 Pin

Requiring Materials :)

   

     1 Arduino

     2 LCD Display

     3 Male to Male Jumper Wires

     4 Bread Board

     5 HCSr04

Before wiring the LCD screen to your Arduino or Genuino board we suggest to solder a pin header strip to the 14 (or 16) pin count connector of the LCD screen.
To wire your LCD screen to your board, connect the following pins:

LCD VSS pin to Arduino GND
LCD VDD pin to Arduino 5V
LCD VO pin to 10k Potentiometer center pin
LCD RS pin to digital pin 12
LCD RW pin to Arduino GND
LCD Enable pin to digital pin 11
LCD D4 pin to digital pin 5
LCD D5 pin to digital pin 4
LCD D6 pin to digital pin 3
LCD D7 pin to digital pin 2
The 10k Potentiometer's other legs connect to +5V and GND
For the backlight of the display, pin 15 (A+) and 16 (K-) of the LCD connect to +5V and GND
If you want, can be use a 220 ohm resistor to power the backlight of the display.


 Previous Video ;)

       

                    LCD#2



Circuit Diagram :)
 
       
Arduino Code :)
         
               HCSr04  

New Ping Libeary :)\
 
            NewPing

Product Link :D

          HCSr04
          LCD Module
          Arduino



Comments

Post a Comment

Popular posts from this blog

How to make a radar using Arduino and Processing IDE

-
Image
How to make a radar using Arduino and Processing IDE In this Arduino Tutorial I will show you how you can make this cool looking radar using the Arduino Board and the Processing Development Environment. You can watch the following video or read the written tutorial below for more details. I connected the Ultrasonic Sensor HC-SR04 to the pins number 10 and 11 and the servo motor to the pin number 12 on the Arduino Board. Now we need to make a code and upload it to the Arduino Board that will enable the interaction between the Arduino and the Processing IDE.  For understanding how the connection works click here to visit my https://youtu.be/By86ma1mpxs Arduino Code:) #include <Servo.h>. // Defines Tirg and Echo pins of the Ultrasonic Sensor const int trigPin = 10; const int echoPin = 11; // Variables for the duration and the distance long duration; int distance; Servo myServo; // Creates a servo object for controlling the servo motor void setup() { pinMode(tr...
Read more

Smart gesture robot

-
Image
smart gesture robot using APDS9960 sensor My Hand gesture Smart mouse using arduino  and APDS9960 Wave your hands and light turns on. Can you believe this magic turns into reality? Meet the Gesture Sensor which offers touch-less gesture sensing - you can issue orders simply with a swipe of your hand! Furthermore, it supports RGB color detecting and ambient light measuring. With this new sensor, traditional switch can be replaced. Operating Voltage: 3.3-5V I2C interface x1 Interrupt pin x1 Detecting range: 100mm (3.94") Module size: 18.3x16.4mm (0.72x0.65") This project shows detecting gestures of hand to RIGHT, LEFT, UP, DOWN and also Ambient color and proximity detection using Arduino module APDS-9960 . Arduino Nano+ RGB and Gesture Sensor(5pin and 6pin, purple board) which control the light bulb - Arduino Nano+RGB and Gesture Sensor APDS-9960(6pin . MY Previous video :)  https://youtu.be/8LVRWCUIVyY #include <Wire.h> #include <SparkFun_APDS9960...
Read more
-
Image
We're done with basics of the NodeMCU in my. Now it's time to use the NodeMCU like how it's meant to be use: as an IoT device. Here I will show you how to create a simple NodeMCU web server which will control a LED attached to one of the NodeMCU's pins. Sounds interesting? Read on! For this to work, you must have already installed the ESP8266 board development toolkit as shown in my  l  Here's the code for our simple nodemcu web server: #include <ESP8266WiFi.h> // Replace with your network credentials const char* ssid = "**********"; const char* password = "**************"; // Set web server port number to 80 WiFiServer server(80); // Variable to store the HTTP request String header; String output5State = "off"; String output4State = "off"; const int output5 = 5; const int output4 = 4; void setup() { Serial.begin(115200); pinMode(output5, OUTPUT); pinMode(output4, OUTPUT); // Set outputs to ...
Read more